Le Workshoppe Rearangeé


I think I did not show you the inside of my workshop, except for the pieces visible around the various pieces of knives and machinery that I have shown in my crafting posts. And since I have totally overhauled (and cleaned) the shop these last few days, I have decided to give you a quick tour of the new layout. The workshop is a bit ad-hoc and furniture is made from mostly scraps.

So let’s start with the north wall, right behind the door.

© Charly, all rights reserved. Click for full size

On the right, you can see where my lathe is stored. I do not use it very often. Right next to the circuit breaker hangs my woodcutting helmet and fire extinguisher.

In the middle of that wall is a huge shelf packed with various things. At the very top are old baking trays, then a plastic tray with some pieces of graphite. Neither of those things I need often, thus the upper shelves. Then come abrasive cloths and papers sorted by grit. Under them are some cleaning, flammable and corrosive chemicals, and a little basket with magnets inside to collect steel dust. Next comes the shelf with various fixtures and jaws for the vice, follows shelf with knives in progress and knife templates, and a shelf with big massive pieces of steel and aluminium. The second shelf from the bottom is now filled with various lubricants and the lowest one currently occupies interesting-looking stones for suiseki and bonsai. The various plastic bottles are mostly sunflower oil for quenching and one bottle for cutting oil.

To the left of the shelf hangs a board with various chisels, scrapers, planers, and knives.

Leaning against the shelf are various wooden dowels, staves, bow staves, pipes, and long wooden prisms.

To the very left, you see the beginnings of my first workbench, made yonks ago. It is three meters long and would not fit in one picture.

© Charly, all rights reserved. Click for full size

Above and below the workbench are cupboards repurposed from kitchen renovations. In the corner, you can see two racks for thin metal profiles and pipes and the motor belongs to my tumbler. I have put it on this part of the workbench because it is somewhat inaccessible to work on and I have nowhere else to put the tumbler where it would not be in the way. I think I will be able to run it from there too, which is a plus.

The red vice is right under a light and in a spot where all the chisels, hammers, saws, rasps, and files are no more than one step away. On the cupboard right above it is also a thermometer so I know how warm/cold it is. Inside the cupboard above the vice are empty plastic containers for when I need them during work (like for example to sort screws into when disassembling/assembling something). In the drawer below it are small files and brushes, in the next drawer various pliers and shears, next wrenches, and the bottom drawer is filled with clamps.

© Charly, all rights reserved. Click for full size

The forge in the middle is there because it needs repairs – work for tomorrow. Under it is a place for storing the table saw when its not in use, a small stool to help me to reach the upper shelves, a bucket for steel dust, and a shop vacuum cleaner.

Above the forge is a shelf with various writing instruments, gomtry tools like compasses, rulers, curves, the most-often used screwdrivers, and a roll of paper kitchen towels. The papers hanging on that shelf are laminated steel heat-treating charts. I will add in near future data sheets for the steels that I use. Inside the cupboard are nails and on the very top shelf accessories for the greenhouses. Again, the upper shelf is occupied with things that are not used often.

Next, you can see my unbender, now permanently fixed to the workbench. I have also spent one more day making it sturdier and improving the design a bit. Next to it, at the end of the bench, is now permanently fixed my drill press. It is lifted slightly above the bench so I can reach under it with a small broom to tease out the metal chips that collect there. I have also put there a piece of PVC flooring to protect the workbench from dripping cutting oil. The tables hanging on the cupboard above it are a drill-speed table for various materials and a conversion table between trizact and grit abrasive ranking.

Below the drill are various small brooms and seldom-used cutting instruments. In the drawers are some abrasives for my handheld belt sander and some ppe, like gloves.

Above the drill press, right at the end of the picture, you can see a small shelf packed with old cookware for when I need to cook something that is not fit to do in the kitchen. Behind it is a small shelf filled with various drill bits.

Now we come to the south wall.

© Charly, all rights reserved. Click for full size

You have already seen my abrasive belt rack and my small heating stove. The basket and plastic bucket are for wood off-cuts. Normally they are not this full, but I did not need to heat the workshop for quite a long time now, obviously. The grey plastic trumpet is a vacuum attachment for collecting wood dust from the belt sander. The black barrel beside it with a similar metal trumpet is for collecting sparks and metal dust.

The green shelf to the left has buckets with various chemicals and abrasives on the top, some drums for the tumbler on the top shelf, and various metal offcuts on the rest.

Now we are reaching the newest addition to my workshop, one that has spurred the complete reorganization – the east wall with a new workbench.

© Charly, all rights reserved. Click for full size

On the right is now permanently affixed my small bandsaw. I hope that fixing it to the bench will reduce its vibrations and improve the lifespan of the saw bands, they were snapping rather quickly.

Below the bandsaw is a small cupboard with bonsaist equipment and various attachments for the belt sander.

The small brown shelf between the windows contains various screws, glues, popsicle sticks, bbq skewers, strings, wooden wedges, metal foils, and a first aid kit. On the right side (out of view except the baseball cap) hang various ppe, like face shield, earmuffs, respirator, and goggles. On the left side hang various bits of wire. Below it is a cordless drill and my two angle-grinders.

And on the left side of the bench is the belt sander. Originally it stood where the unbender is now, and it was a pain in the nether regions. It got in the way of reaching the cupboards and working on the drill press and it ate a lot of the workbench so some manual works were awkward or even impossible. Here it should not be in the way and there is enough space to the right side of it to build various attachments – I plan a lathe, a drum sander, and a disc sander.

The drawers in the grey cupboard below contain various measuring instruments, ball bearings, cork, popsicle sticks, and some other various stuff.

In the cupboard itself are boxes with assorted screws, spacers, springs, locks, keys, handles, and similar small diverse things that do not fit anywhere else.

Between the cupboard and the new workbench is about 9 cm space. I have thought about what to do with it and I have decided that it would be an ideal storage space for all of my knife- and tool-making steels, so I have put them there.

And on the very left of the picture you see where my various electric cables and gas burners hang.

That was the grand tour through my small workshop. Writing it took a lot longer than I have expected, I hope I did not bore you to death.

Comments

  1. Jazzlet says

    Your workshop looks extremely practical and well thought out. I am looking forward to seeing what you make in it next :-)

  2. Matthew Currie says

    Saw bands: could you be running with too little tension? They should make a nice sound when twanged.

  3. says

    @Matthew Currie, that could be it. There is no way for me to measure the tension and I have no idea how strong to make it so I might be overcautious with it. The problem is that the tool manual is not very specific and I have no one experienced around who could explain and show it to me, as it were, in the wild.

  4. Matthew Currie says

    No, there’s usually no good gauge for tension, but as a general rule, the free side of the blade (opposite the guides) should make a pretty decent musical twang when it’s tightened right. It’s hard to guess the exact pitch, but I have a couple of 12 inch bandsaws with shallow blades, and they work pretty well somewhere around the G string of a fiddle.

Leave a Reply